Hello, We have vSAN cluster which consists of 6 hosts, now we have another 3-tier cluster ( Servers connected to IBM storage) How do we migrate from vSAN to IBM ?
Hello Kinnison, Thank you for reply When I mention local datastore, I mean OS disk. vSAN ready nodes come with an M.2 SSD (ATA disks depending on configuration) in Raid-1 where we will install ESXi...
See more...
Hello Kinnison, Thank you for reply When I mention local datastore, I mean OS disk. vSAN ready nodes come with an M.2 SSD (ATA disks depending on configuration) in Raid-1 where we will install ESXi. In my situation, the OS drive is 256 GB, which does not appear for a few hosts after the update. vSAN storage is completely different. i will be opening a case Based on article https://masteringvmware.com/local-datastore-not-visible-in-esxi-7/#:~:text=So%20in%20case%20of%20ESXi,change%20in%20the%20ESXi%20architecture. if disk size more than 128 GB you should be able to see.
Hello Kinnison, Thank you for responding. VMware vSAN Ready nodes (Dell Servers)... and yes, I did check compatibility and it is supported. I upgraded from 6.7 to 7.0U3 Dell customized image. and...
See more...
Hello Kinnison, Thank you for responding. VMware vSAN Ready nodes (Dell Servers)... and yes, I did check compatibility and it is supported. I upgraded from 6.7 to 7.0U3 Dell customized image. and update been done via lifecycle manager. all hosts updated successfully but some hosts doesnt show local datastore and some hosts does show local datastore ( all using same build number 7.0U3)
Hello, I recently updated from 6.5 u3 to 7.0 u3. I no longer see a local datastore on a few hosts after upgrading, although I see a local datastore on other hosts running ESXi 7.0u3. 2x M.2 SSDs is...
See more...
Hello, I recently updated from 6.5 u3 to 7.0 u3. I no longer see a local datastore on a few hosts after upgrading, although I see a local datastore on other hosts running ESXi 7.0u3. 2x M.2 SSDs is 256 GB. (where ESXI OS residing)
Thank you @maksym007 for the reply, Yes, ESXi is in a cluster with HA and DRS enabled. i will change vCenter and then ESXi. But will that cause any issue to the DR vcenter which is in linked mode?
Hello, I need to change IP address of vcenter and ESXi to different subnet. i have two sites Prod and DR in linked mode vCenter in linked mode and three ESXi on both sites. What is the sequence i...
See more...
Hello, I need to change IP address of vcenter and ESXi to different subnet. i have two sites Prod and DR in linked mode vCenter in linked mode and three ESXi on both sites. What is the sequence i need to follow to change IP address of vCenter and ESXi Note: vCenter is in linked mode
But for below configuration configure vmkernel and physical adapter as MTU 9000 and vSwitch as MTU 1500. Does vSwitch does de-fragmentation or simply it will fail to send frames. When i was m...
See more...
But for below configuration configure vmkernel and physical adapter as MTU 9000 and vSwitch as MTU 1500. Does vSwitch does de-fragmentation or simply it will fail to send frames. When i was migrating standard switch to Distributed switch. Accidently DS switch MTU was set to 1500 and When i migrated vSAN VM kernel i lost connection and VMs were shut down. i was trying to figure out is it because of MTU 1500? logs 2022-09-12T12:05:12.655Z cpu2:3987430)Uplink: 5942: vmnic4: TSO packet has large MSS (8948) plus L7 offset (66), which can't be fit into MTU (1500) 2022-09-12T12:05:12.655Z cpu0:3987430)Uplink: 5942: vmnic4: TSO packet has large MSS (8948) plus L7 offset (66), which can't be fit into MTU (1500) 2022-09-12T12:05:12.655Z cpu0:3987430)Uplink: 5976: vmnic4: Non TSO L2 payload size exceeds uplink MTU. FrameLen: 3134, L3 header offset: 14
Hello, I created pem file with full chain (Wildcard Domain cert+ intermediate+root ) and private key. i am following the below article. https://docs.vmware.com/en/VMware-Cloud-Director/10.3/VMware...
See more...
Hello, I created pem file with full chain (Wildcard Domain cert+ intermediate+root ) and private key. i am following the below article. https://docs.vmware.com/en/VMware-Cloud-Director/10.3/VMware-Cloud-Director-Install-Configure-Upgrade-Guide/GUID-74296A4D-416F-4D7F-BBD6-BA983AAAD4E7.html cmd: /opt/vmware/vcloud-director/bin/cell-management-tool certificates -j --cert /opt/vmware/vcloud-director/etc/user.http.pem --key /opt/vmware/vcloud-director/etc/user.http.key --key-password imported_key_password what is imported_key_password here? is it the root password for appliance?
Dear Community, i set vmkernel 9000 and vDS standard switch 1500 and Physical switch set to 9000 is this configuration supported or it will create network issues
Hello, I have to change IP address of vcenter and vsphere replication. which IP change first and what is procedure to change IP address of vsphere replciation
i was able to remove VIBS using force upgrade was successful. to remove VIB- esxcli software vib remove -n scsi-bfa -f to see the output without actually removing VIB - esxcli software vib remove...
See more...
i was able to remove VIBS using force upgrade was successful. to remove VIB- esxcli software vib remove -n scsi-bfa -f to see the output without actually removing VIB - esxcli software vib remove -n scsi-bfa -f --dry-run
if you already have PEM files and Private KEY please follow the below article https://docs.vmware.com/en/VMware-Cloud-Director/10.3/VMware-Cloud-Director-Install-Configure-Upgrade-Guide/GUID-DD6CC...
See more...
if you already have PEM files and Private KEY please follow the below article https://docs.vmware.com/en/VMware-Cloud-Director/10.3/VMware-Cloud-Director-Install-Configure-Upgrade-Guide/GUID-DD6CC590-DA49-4700-AD7F-12E9631DDBAF.html if you are using wildcard follow the below article https://docs.vmware.com/en/VMware-Cloud-Director/10.3/VMware-Cloud-Director-Install-Configure-Upgrade-Guide/GUID-DD6CC590-DA49-4700-AD7F-12E9631DDBAF.html note user.http.key is your private key of your pem file
Thank you for responding. There is no problem with the certificate. If I log in as Org admin, I can view the plugin. However, if I login as a user to whom I granted all read access from the user rol...
See more...
Thank you for responding. There is no problem with the certificate. If I log in as Org admin, I can view the plugin. However, if I login as a user to whom I granted all read access from the user role. He is unable to view the plugin.
Hello, I am attempting to upgrade a server from 7.0.1 to 7.0.3 and it fails with below decencies packages. is it safe to remove? and when i try to remove one of VIB net-mst (mellanox) it doesnt rem...
See more...
Hello, I am attempting to upgrade a server from 7.0.1 to 7.0.3 and it fails with below decencies packages. is it safe to remove? and when i try to remove one of VIB net-mst (mellanox) it doesnt remove, how can i proceed upgrade process
In vCD, I created a user and granted read-only access. The user can see plugins that are associated with vCD. and he can't see the when he clicks on any plugin. Any suggestions? The user should hav...
See more...
In vCD, I created a user and granted read-only access. The user can see plugins that are associated with vCD. and he can't see the when he clicks on any plugin. Any suggestions? The user should have read-only access to the vCD and plugins. Any suggestions? error ss
