Hi I deployed NSX Standalone Edge on-premise because I wanted to extend L2, but I can't log in with the password I set. Is there any default password? Best regards
Hi p0wertje Thank you for your reply. I think the control plane is integrated into Manager since NSX-T 2.4. Is it okay to assume that even if NSX-T Manager stops completely, there will be no impac...
See more...
Hi p0wertje Thank you for your reply. I think the control plane is integrated into Manager since NSX-T 2.4. Is it okay to assume that even if NSX-T Manager stops completely, there will be no impact? In this case, it is beyond the scope of control plane , so I imagine that it will have an impact. For example, if NSX-T Manager stops completely, I think that the network created by NSX-T Manager will not be usable. Best Regards.
Hi I am currently testing the NSX-T Mnagaer for failure. Will the network created by NSX-T Manager or the network extending L2 from on-premises become unusable if the NSX-T Mnager fails? Best Rega...
See more...
Hi I am currently testing the NSX-T Mnagaer for failure. Will the network created by NSX-T Manager or the network extending L2 from on-premises become unusable if the NSX-T Mnager fails? Best Regards.
Hi I am currently conducting a failure test during the HCX migration. If I stop HCX-Manager or HCX-IX during the migration, the migration will result in an error. Is this a specification move? A...
See more...
Hi I am currently conducting a failure test during the HCX migration. If I stop HCX-Manager or HCX-IX during the migration, the migration will result in an error. Is this a specification move? Also, does the above error occur regardless of the migration direction? For example, in the case of "on-premises → Cloud" migration, I would like to know if there are cases where the migration will continue even if the Manager on the Cloud side stops. Best regards.
Hi ChrisFD2. I tried to verify. I have confirmed that REDEPLOY is done by removing the appliance and then resyncing. (WAN was not in the environment, so only IX and NE...) Follow the steps below ...
See more...
Hi ChrisFD2. I tried to verify. I have confirmed that REDEPLOY is done by removing the appliance and then resyncing. (WAN was not in the environment, so only IX and NE...) Follow the steps below as a basic recovery method in the event of a failure on the three appliances. 1. Deletion of failed appliance 2. Run resync from Service Mesh (Appliance RED EPLOY) Best Regards.
Hi ChrisFD2. Thank you reply messages. I need to remove the existing Service Mesh before redeploy, or should I operate from "EDIT SERVICE MESH" and FINISH?
Hi I would like to know how to recover from a failure in the following components. ・HCX NetworkExtention ・HCX Interconnect ・HCX WAN Optimization If there is a way other than redeploying Service ...
See more...
Hi I would like to know how to recover from a failure in the following components. ・HCX NetworkExtention ・HCX Interconnect ・HCX WAN Optimization If there is a way other than redeploying Service Mesh, I would appreciate it if you could tell me the procedure.
Thank you for your reply, ChrisFD2. Is there a way to enable WEB UI and monitor bandwidth from WAP OPT?I want to be able to see a screen like "capture2.png", but can I only use support?I want to che...
See more...
Thank you for your reply, ChrisFD2. Is there a way to enable WEB UI and monitor bandwidth from WAP OPT?I want to be able to see a screen like "capture2.png", but can I only use support?I want to check the transfer speed at the time of migration.
I would like to enable the WEB UI of HCX WAN Optimizer.However, I was asked for login information and I searched for the documentation but could not find it.If you skip it, the settings will not be r...
See more...
I would like to enable the WEB UI of HCX WAN Optimizer.However, I was asked for login information and I searched for the documentation but could not find it.If you skip it, the settings will not be reflected.What is the user/password to enter here?
