All Posts

  Need bug id and url for velocloud Interface error issue   Symptoms When you go to the remote diagnostic and hit on the Interfaces status you will get an error. Cause When you go to the remote diagnostic and hit on the Interfaces status you will get an error.   Impact/Risks During any tshooting, Interace status won't show up which may delay in resolution Resolution A fix for issue included in 4.3 and above Workaround the workaround is to reboot the edges

Need details info and url for bug on velocloud   Symptoms For BGP filter changes, Velos do not perform a delta check at per filter change granularity but rather retract all filters and reinsert them as per the new BGP configuration. Cause This can induce a window (of a few seconds) where expected filters would momentarily disappear and re-appear, which can likely cause route churn (add/remove routes) based on filters.   Impact/Risks There is a potential for a brief interruption when making this change.

Greetings!,   We are running into a interesting situation. We are rolling our VeloCloud Edge 610s to over 500 locations. These locations have 10 VLANs/Subnets with subnets sizes from /26 to /30s. We have a Edge 3800s is a cluster in our data center. All Edges are on version 4.3.1. Our issue is the number of routes that we are receiving is crushing our router in the data center. We have come up with remedies to address this on the routers but is messy.. My question is can the Velo Edge 3800 summarize the BGP routes? Example: Site 42  VLAN 5 10.2.x.0/28 vlan 10 10.2.0.16/28 vlan 15 10.2.0.32/27 So all these routes as expected come into our data center.. Can we configure the Edge 3800 to summarize all the 10.2.x.x to a 10.2.0.0/24 so that way we only get 1 route redistributed rather than in our case 10 subnets for each site?       

what is the exact meaning of advertising the default route into overlay on sdwan. or Default route is not propagated via overlay. does it mean there will be not default route on sdwan appliance? i am trying to figure it out pros and cons of above..

I have successfully initiated the Virtual VeloCloud Edge on KVM (EVE-NG). The vEdge is provisioned to the VCO. But the edge lost configuration or is unable to communicate with VCO after Turning off or shutting down the vEdge. Power ON the vEdge, the vEdge boot is in the factory default setting. The issue is that when I turn Off the vEdge and turn On again, the vEdge boot in the default configuration needs to activate again.  I am working on a test lab on EVE-NG/PNETLAB and as we know that EVE-NG/PNETLAB are suing the KVM. -----Cloud.init.iso or cdrom.iso--------- meta-data: instance-id: vEdge local-hostname: vEdge network-interfaces: GE3: type: static ipaddr: 192.168.100.111 netmask: 255.255.255.0 gateway: 192.168.100.240 user-data: #cloud-config password: velocloud chpasswd: { expire: False } ssh_pwauth: True Thanks and Regards

VMware SD-WAN documents in Greek are published on the VMware Docs platform. You can find the Greek version of documentation at VMware SD-WAN Documentation, VMware SASE Documentation, VMware Secure Access Documentation, and VMware Cloud Web Security Documentation.

VMware SD-WAN documents in Greek are published on the VMware Docs platform. You can find the Greek version of documentation at VMware SD-WAN Documentation, VMware SASE Documentation, VMware Secure Access Documentation, and VMware Cloud Web Security Documentation.

VMware SD-WAN documents in Greek are published on the VMware Docs platform. You can find the Greek version of documentation at VMware SD-WAN Documentation, VMware SASE Documentation, VMware Secure Access Documentation, and VMware Cloud Web Security Documentation.

VMware SD-WAN documents in Greek are published on the VMware Docs platform. You can find the Greek version of documentation at VMware SD-WAN Documentation, VMware SASE Documentation, VMware Secure Access Documentation, and VMware Cloud Web Security Documentation.

VMware SD-WAN documents in Greek are published on the VMware Docs platform. You can find the Greek version of documentation at VMware SD-WAN Documentation, VMware SASE Documentation, VMware Secure Access Documentation, and VMware Cloud Web Security Documentation.

Good day! With the help of the API, I collect data about the Package Drop and TCP RTT from vrni. Periodically, values 200% Packet Drops come. How is this possible? Here is my api json request - { "entity_type": "Flow", "filter": "source_ip.ip_address = '$ip' and destination_ip.ip_address != '52.109.*' and destination_ip.ip_address != '20.191.*'", "aggregations": [ { "field": "flow.packetDrop.ratio.average.percent", "aggregation_type": "AVG" } ], "time_range": { "start_time": '$curtime-minus-4m', "end_time": '$curtime-minus-3m' }}' Also, please tell me why the data arrives with a 15 minute delay? What additional settings need to be made?