any ideas ?
The problem is that the DS3 database never completely got built. Per the below output from ConfigDS3DB_0.txt, the reviewshelpfulness table failed the check (this is the longest step in the database creation process):
Checking the contents of Tables = reviewshelpfulness
ERROR: DS3 value check failed.
============================================================================
--------------------------------------------------------------------------
FAIL: DS3 is either not built completely or not in initialized state.
--------------------------------------------------------------------------
04:50:18 PM: DS3 checker script finished..
04:50:18 PM: DS3 DB check failed..
Per the User's Guide on page 50:
"Wait for the DS3DB0 creation process to complete; depending on your environment, this can take 12 hours or more. To determine if it’s complete, follow these steps:
a In a terminal window on the prime client, run the following command:
ssh <DS3DB0-IP-address> ‘tail -f /ds3/VMmark3-DS3installoutput.txt’
(where <DS3DB0-IP-address> is the IP address of the DS3DB0 VM, which can be found in the hosts-stub.txt file referenced above).
b Watch for the following text: VMmark3 DS3DB Setup Completed : Rebooting"
Unfortunately, I think you'll need to re-provision your tile 0 again, and wait until you see the "DS3DB Setup Completed".
Hi, could you please perform the following steps so we can troubleshoot further?
1. From your primeclient VM, attach the VMmark3.properties you used to run the benchmark (/root/VMmark3/VMmark3.properties)
2. From your primeclient VM, ZIP and attach the configfiles subdirectory from your most recent run:
cd /root/VMmark3/results/Results_2018* (note: make sure you choose the most recent failed run directory)
zip -r /root/configfiles.zip configfiles
Then attach the resulting /root/configfiles.zip
3. From your DS3DB0 VM, attach the output of these commands:
cd /root/VMmark3/client/DS3DB
./DS3_checker.sh
please standby ...
The problem is that the DS3 database never completely got built. Per the below output from ConfigDS3DB_0.txt, the reviewshelpfulness table failed the check (this is the longest step in the database creation process):
Checking the contents of Tables = reviewshelpfulness
ERROR: DS3 value check failed.
============================================================================
--------------------------------------------------------------------------
FAIL: DS3 is either not built completely or not in initialized state.
--------------------------------------------------------------------------
04:50:18 PM: DS3 checker script finished..
04:50:18 PM: DS3 DB check failed..
Per the User's Guide on page 50:
"Wait for the DS3DB0 creation process to complete; depending on your environment, this can take 12 hours or more. To determine if it’s complete, follow these steps:
a In a terminal window on the prime client, run the following command:
ssh <DS3DB0-IP-address> ‘tail -f /ds3/VMmark3-DS3installoutput.txt’
(where <DS3DB0-IP-address> is the IP address of the DS3DB0 VM, which can be found in the hosts-stub.txt file referenced above).
b Watch for the following text: VMmark3 DS3DB Setup Completed : Rebooting"
Unfortunately, I think you'll need to re-provision your tile 0 again, and wait until you see the "DS3DB Setup Completed".
That error is very strange to be happening this far into the benchmark.
Here are some troubleshooting steps:
1. Attach the /etc/hosts from your PrimeClient VM
2. Before the benchmark, and after you see that error, run these commands from your PrimeClient VM:
[root@primeclient VMmark3]# staf client0 ping ping
[root@primeclient VMmark3]# ping -c 5 client0
3. If either of the commands from step 2 fail, can you check to see whether the Client0 VM is still powered on? If not, look at vCenter to see if/why that VM got powered off.
Finally, please check that these hosts/VMs are on an isolated/private network (i.e. no DHCP servers or other VMs/hosts that could potentially cause IP address conflicts).