I like to know if it is possible to install esxi3.5 on xseries 226, I have read on ibm books that is in HCL only esx 3.0
thanks
Have you checked the HCL yourself? It's available in the documentation section of the VMware Support site (http://www.vmware.com/support/pubs) under the VI documentation, then ESXi. It's called the System Compatibility Guide.
Y es, I have checked and only is availalbe with esx3, but I like to know if it is possible to add support to a machine in ESXI or ESX3.5
thanks
It's unlikely to be supported, but ESXi may run fine on it. What sort of storage controller and NIC does it have? Are you able to get the specific PCI ids for those 2 devices?
ESX 3.5 Does run on it but it did not work on the local SATA controller, I had to put an adaptec card in it.
Thanks for you answers. I have a SATA controller serveraid7t and de NIc is on motherboard, I'll try to install on esxi and esx3.5
I hope that this can wordk
thanks
I have the same situation xseries 226 with serveraid 7t with four SATA disk and nic integrated in motherboard and I like no tkno if ESX can work (es3.5 or esxi)
what are you results with this configuration?
Thanks
klxout,
I'm running ESXi on an IBM x220 which is much older than your X226. Runs perfect! Only thing is that it can't monitor voltage, fans, etc etc.
My X220 has three SCSI disks that are not on RAID.
You can take a look at this page to see if ESXi with recognize the serveraid 7t - http://www.vm-help.com/esx/esx3i/Hardware_support.php.
First of all, thanks for your answer.
I have checkes and serveraid 7t (it is an adaptec 2410 SA) and in this page appears. But I have installed esxi in this server and after first reboot all seems to work correctly, but after secodn reboot I have obtained a kernel panic, and I can't boot the system
What can I do?
Thanks
Klxout,
Do you have any more info on the Kernel Panic? Any additional error messages?
hello.
i've the same question.
i try to install esx 3.5i u3 on an ibm 226. it has an adaptec host raid with scsi disk in Raid 1.
at the install, esx load the aic79xx module successfully, but it shows the two disks instead of the array.
does anybody have the same problem ? is there a solution ?
thanks a lot
Welcome to the VMware Community forums. The drivers that come with ESX(i) don't support HostRAID so you'll only be able to use individual drives.
Hi to everybody! Did somebody installed succesfully ESXi 3.5 or ESX 3.5 on either systems listed below? (I need to install ESXi on this 2 systems) Thanks in advance. Best regards.
IBM eServer xSeries 225:
2x Intel Xeon 2666 Mhz.
4 Gb RAM.
IBM ServeRAID 5i (2 SCSI disks 67 Gb/ 136 Gb)
Broadcom NetXtreme Gigabit Ethernet.
IBM eServer xSeries 226:
2x Intel Xeon 3200 Mhz.
4 Gb RAM.
IBM ServeRAID 6i (1 SCSI disk 294 Gb)
Broadcom NetXtreme Gigabit Ethernet.
Hi,
I have been using for some time (months at least) ESXi 3.5 on a xSeries 226 server:
9GB RAM
2 XEON 3.2 CPUS
IBM ServeRaid with 6 SCSI 145GB disks
with no mayor issues. Only thing is there is little monitoring of hw details (fans, power supplys, etc). But the system has been rock solid.
I was only wondering if the new version (I think ESX 4) works, but still do not know if there are enough nice new things to justify changing. Only thing I would really like is console for Linux and ... Mac OS X