Hello,
I am new user, and try to install in a test machine. I retried today with V3.0.2, and I have the same error I had with V3.0.1
I made sure that I followed the HCL, and I have
The right Intel board, The right Adaptec controler, in Mirror,
I managed to install except the VMFS3 does not show up.
It is partitioned in SAD3 I checked using the appropriated command fdsk etc... and it is around 140GB.
But When the system tries to mount /sda3/vmfs3 in the boot sequence, there is an error. Even if I look using vdh -l, the same error occurs.
Anyone has an IDEA... I am really confused here !
Regards.
J.
error in dmesg
\----
PCI: Enabling device 05:01.1 (0156 -> 0157)
scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 2.0.12
SCSI device sdb: 286749488 512-byte hdwr sectors (146816 MB)
sdb:
error in vmkernel
\----
Aug 1 10:26:43 esxsrv1 vmkernel: 0:00:00:45.792 cpu7:1036)IDT: 1725:
Aug 1 10:26:43 esxsrv1 vmkernel: 0:00:00:45.792 cpu0:1024)VMNIX: Mod: 2080: Plugging 005:01.1
Aug 1 10:26:43 esxsrv1 vmkernel: 0:00:01:13.489 cpu0:1024)VMNIX: VGA: 425: 1
Aug 1 10:26:43 esxsrv1 vmkernel: 0:00:01:13.489 cpu0:1024)VMNIX: VGA: 425: 2
Aug 1 10:26:43 esxsrv1 vmkernel: 0:00:01:13.489 cpu0:1024)VMNIX: VGA: 425: 3
Aug 1 10:26:43 esxsrv1 vmkernel: 0:00:01:13.497 cpu0:1024)VMNIX: VGA: 425: 4
Aug 1 10:26:43 esxsrv1 vmkernel: 0:00:01:13.497 cpu0:1024)VMNIX: VGA: 425: 5
Aug 1 10:26:43 esxsrv1 vmkernel: 0:00:01:13.497 cpu0:1024)VMNIX: VGA: 425: 6
Aug 1 10:26:43 esxsrv1 vmkernel: 0:00:01:13.497 cpu0:1024)VMNIX: VGA: 425: 7
Aug 1 10:26:43 esxsrv1 vmkernel: 0:00:01:28.228 cpu0:1024)IOAPIC: 1080: 0x51 retriggerred
Aug 1 10:26:44 esxsrv1 vmkernel: 0:00:01:52.545 cpu0:1024)Loading module vmfs2 ...
Aug 1 10:26:44 esxsrv1 vmkernel: 0:00:01:52.547 cpu0:1024)Mod: 217: Starting load for module: vmfs2 R/O length: 0x11000 R/W length: 0x11000
Aug 1 10:26:44 esxsrv1 vmkernel: 0:00:01:53.716 cpu7:1037)Mod: 430: Module vmfs2: initFunc: 0x826ab8 text: 0x818000 data: 0x1ef8d40 bss: 0x1ef8f40
Aug 1 10:26:44 esxsrv1 vmkernel: 0:00:01:53.716 cpu7:1037)Mod: 446: mainHeap avail before: 13601912
Aug 1 10:26:44 esxsrv1 vmkernel: 0:00:01:53.716 cpu7:1037)FSS: 265: Registered fs vmfs2, module 4, fsTypeNum 0xf520
Aug 1 10:26:44 esxsrv1 vmkernel: 0:00:01:53.716 cpu7:1037)Mod: 471: Initialization for vmfs2 succeeded.
Aug 1 10:26:44 esxsrv1 vmkernel: 0:00:01:53.716 cpu7:1037)Module loaded successfully.
Aug 1 10:26:44 esxsrv1 vmkernel:
Aug 1 10:26:44 esxsrv1 vmkernel: 0:00:01:53.721 cpu7:1037)Mod: 501: mainHeap avail after: 13600600
Aug 1 10:26:44 esxsrv1 vmkernel: 0:00:01:53.721 cpu7:1037)Mod: 509: no private ID set
Aug 1 10:26:44 esxsrv1 vmkernel: 0:00:02:03.945 cpu5:1038)World: vm 1056: 690: Starting world vmware-vmkauthd with flags 4
Aug 1 10:26:44 esxsrv1 vmkernel: 0:00:02:12.668 cpu2:1056)World: vm 1056: 3864: Killing self with status=0x0:Success
Aug 1 10:26:44 esxsrv1 vmkernel: 0:00:02:37.493 cpu0:1024)VMNIX: VSI: 396: node 1080: get=d21f17b8 set=d21f1868 list=d21f1784 by ra=d21f1637
Aug 1 10:26:44 esxsrv1 vmkernel: 0:00:02:37.493 cpu0:1024)VMNIX: VSI: 396: node 1081: get=d21f1870 set=d21f1894 list=d180e580 by ra=d21f1650
Aug 1 10:26:44 esxsrv1 vmkernel: 0:00:02:57.861 cpu7:1037)Config: 384: "Enabled" = 0, Old Value: 0, (Status: 0xbad005f)
Aug 1 10:37:37 esxsrv1 vmkernel: 0:00:14:30.407 cpu7:1037)WARNING: SCSI: 7619: Unknown adapter vmhba0
Aug 1 10:37:37 esxsrv1 vmkernel: 0:00:14:30.407 cpu0:1024)VMNIX: WARNING: VmkDev: 769: status=0xbad000f
What Adaptec controller do you use?
According to the logs the disks are NOT mirrored.
Adaptec 39320A Ultra 320 Firmaware just updated to latest V4.30
Still the same problem.
If I go the the Adaptec BIOS, I see the disk are Mirrored.
Also in the boot sequence, I have this
Startng VMware late init tools \[ok]
Loading VMkernel module VMFS2 \[ok]
could not open '/vmfs/volumes'.
Error : no such file or directories
Restoring NAS volume Error performing operation : SysinfoException: NodeId(212) ; status(195887107) = Not Found; Message = Unable to get instance list
Restoring S/W iScsi volumes \[ok]
Well
1) I dont have iScsi volumes, just plain Seagate on an Adaptec
2) I just boot in trouble shooting and create the directory /vmfs/volumes... The error complaining about could not open disapeared, but all other errors about Device ID and NAS volume Error remains
3) something I forgot to mentioned, I cannot log on the console after all this. I have the message
Loading Module vmfs2 ....
Module Loaded successfully
and it hangs there.
I am able to VirtualInfrastructure Client for my hostname, and see that there is no datastore present
Hum...
Ok,
1) I updated the Firmware of the Adaptec controler.
2) I deleted the mirror, and recreated a Raid 1
1 hour later, I reinstall from the CD, When comes the time to choose on which disk to install, the installation process proposes me the 2 seagates drive I have /sda or / sdb.
Is it normal. Should it not proposed only the Raid ?
Maybe that is the problem no ? Since it is my first installation I cannot relate to what is normal or not.
Can u provide feedback.
Regards
J.
This seems to be your problem.
ESX doesn't recognize the RAID.
OK I decided to change the Controler. I used a
SCSI RAID 2200S from Adaptec rather than a 39320A Ultra 320 SCSI
I realized reading some other atricles in the KB that even if the Controler appears on the compatibility list, and that the device is RAID capable, it does not make it a candidate for a VMFS partition. It must be explicitly identify as RAID as a device model in the IO Compatibility Guide.
I must admit the documentation could be clearer !!!! I would have save me 8 hours of frustration.
Tks anyway.
J.