Greetings -
My ESXi server's VGA console (LCD panel with a standard PS/2 keybd) is blank and I can't seem to convince ESXi to wake it up. No key strikes wake it up at all. I know the panel is fine because I can hook it to another server and it lights right up. And, if I absolutely need to, I can reboot the ESXi server to wake the panel up. But I'd rather not do that if I can avoid it.
Is there some sneaky way via the server's CLI that I can kick the video card awake? I know BusyBox is pretty limited in what it allows so I'm guessing I'm out of luck.
Any suggestions? 🙂
Thanks!
jas
How about trying a different keyboard ?
piaroa wrote:
How about trying a different keyboard ?
I can certainly try that, assuming I can find another one that isn't being used. 🙂 Thanks for the suggestion.
I agree with piaroa, changing the keyboard should solve the issue. However make sure you use an USB keyboard (not PS/2). Only an USB keyboard will be discovered dynamically. Hot plugging a PS/2 device (mouse or keyboard) could destroy the PS/2 controller in the worst case!
There were changes in the way the keyboard is discovered. Read http://kb.vmware.com/kb/1011852 for details. The article is for ESX 3.5, therefore the solution does not help you, however it describes the issue.
André
André Pett wrote:
I agree with piaroa, changing the keyboard should solve the issue. However make sure you use an USB keyboard (not PS/2). Only an USB keyboard will be discovered dynamically. Hot plugging a PS/2 device (mouse or keyboard) could destroy the PS/2 controller in the worst case!
I agree that hot-plugging a PS/2 keyboard is a bit risky, but it's all I have available at the moment (it's been YEARS since I've purchased a new computer w/keyboard... heh heh..). That said, I hear what you're saying and will have to buy a USB keyboard for it. Fortunately they're dirt cheap.
Thanks for the pointers. I'll check back into this thread when I've obtained the keyboard and report.
jas
André Pett wrote:
I agree with piaroa, changing the keyboard should solve the issue. However make sure you use an USB keyboard (not PS/2). Only an USB keyboard will be discovered dynamically. Hot plugging a PS/2 device (mouse or keyboard) could destroy the PS/2 controller in the worst case!
No luck. I found a working USB keyboard and tried that, but nothing happened. The display is still blanked out.
Is there no CLI trick I can do from an ssh session into the hypervisor that might tickle it awake?
Thanks!
jas
With either keyboard connected do you get a capslok or numlock light to respond. If not you may have a hung process or very busy host. I would try to access the Tech Support mode console (unsupported consoleprior to 4.1) I have had such problems in the past and shut down as many less important guests as I could from within the guest OS. At some point I was able to get control of the console again. I eventually shut down the guests and restarted the Host.
David Stavert wrote:
With either keyboard connected do you get a capslok or numlock light to respond.
Yep. Both keyboards respond to caps/num lock. The machine is mostly idle. The VMs running on it are all fairly low-load.
Other ideas?
jas
I would try another monitor or at least make sure the VGA plug is firmly attached. Unplug and replug. If this is a KVM try the plug unplug routine on both ends of the cable. If KVM try another cable location.
David Stavert wrote:
I would try another monitor or at least make sure the VGA plug is firmly attached. Unplug and replug. If this is a KVM try the plug unplug routing on both ends of the cable. If KVM try another cable location.
I don't have another monitor to try, and I'm 100% certain it's not the monitor. It, and the cable it's attached to both work fine on another server. No KVM involved.
jas
Just a thought. Did you try "ALT-F2" to get to the DCUI screen.
André
Turns out it was a hardware issue. The video card decided it didn't want to send output via it's VGA port (15-pin) but rather it's DVI one. I found an unused DVI->VGA adapter, connected it to the card, moved the LCD panel to it, and voila. I have my console.
Thanks for all the other suggestions though.
jas