VMware Cloud Community
gboskin
Enthusiast
Enthusiast
Jump to solution

Configure ESX hosts to send SNMP traps to a third party server

Can anyone please advise how to configure ESX host ( 3.5) to send SNMP traps to a third party server ...say (10.60.0.1)

0 Kudos
1 Solution

Accepted Solutions
AWo
Immortal
Immortal
Jump to solution

2) It looks like its only sending traps if there is an error or fault on the hots and i need it to send performance stats regularly

If this is possible depends on what VMware put into the MIB's and agents.

You can check for performance metrics in the MIB and I assume that when they exist they are not send as a trap but they need to be requested via a SNMP get from the management suite.


AWo

VCP / vEXPERT 2009

vExpert 2009/10/11 [:o]===[o:] [: ]o=o[ :] = Save forests! rent firewood! =

View solution in original post

0 Kudos
5 Replies
AWo
Immortal
Immortal
Jump to solution

1. Open the firewall for port SNMP 162 UDP.

2. Add these lines to your "/etc/snmp/snmpd.conf":

The trap community name: "trapcommunity public"

The target: "trapsink AWo

VCP / vEXPERT 2009

Edited by AWo

vExpert 2009/10/11 [:o]===[o:] [: ]o=o[ :] = Save forests! rent firewood! =
0 Kudos
azn2kew
Champion
Champion
Jump to solution

Depends on what SNMP agents you're using Dell Open Manage, IBM Director, HP SIM, SCOM using nWorks management packs etc...but anyways, using instructions below should work http://lewanps.wordpress.com/2009/02/23/how-to-setup-snmp-on-esx-35-servers/

If you found this information useful, please consider awarding points for "Correct" or "Helpful". Thanks!!!

Regards,

Stefan Nguyen

VMware vExpert 2009

iGeek Systems Inc.

VMware, Citrix, Microsoft Consultant

If you found this information useful, please consider awarding points for "Correct" or "Helpful". Thanks!!! Regards, Stefan Nguyen VMware vExpert 2009 iGeek Systems Inc. VMware vExpert, VCP 3 & 4, VSP, VTSP, CCA, CCEA, CCNA, MCSA, EMCSE, EMCISA
gboskin
Enthusiast
Enthusiast
Jump to solution

Thanks for all yor response i have installed snmp from the article

i have also set up my host to send traps

i have also sent test traps and can see the traps on my monitoring server ..my problem now is ...

1) i need to interpret the oids been sent to my monitoring server

2) It looks like its only sending traps if there is an error or fault on the hots and i need it to send performance stats regularly

0 Kudos
AWo
Immortal
Immortal
Jump to solution

2) It looks like its only sending traps if there is an error or fault on the hots and i need it to send performance stats regularly

If this is possible depends on what VMware put into the MIB's and agents.

You can check for performance metrics in the MIB and I assume that when they exist they are not send as a trap but they need to be requested via a SNMP get from the management suite.


AWo

VCP / vEXPERT 2009

vExpert 2009/10/11 [:o]===[o:] [: ]o=o[ :] = Save forests! rent firewood! =
0 Kudos
TomHowarth
Leadership
Leadership
Jump to solution

Read the following post for a full explaination http://lewanps.wordpress.com/2009/02/23/how-to-setup-snmp-on-esx-35-servers/

If you found this or any other answer useful please consider the use of the Helpful or correct buttons to award points

Tom Howarth VCP / vExpert

VMware Communities User Moderator

Blog: www.planetvm.net

Contributing author for the upcoming book "[VMware vSphere and Virtual Infrastructure Security: Securing ESX and the Virtual Environment|http://my.safaribooksonline.com/9780136083214]”. Currently available on roughcuts

Tom Howarth VCP / VCAP / vExpert
VMware Communities User Moderator
Blog: http://www.planetvm.net
Contributing author on VMware vSphere and Virtual Infrastructure Security: Securing ESX and the Virtual Environment
Contributing author on VCP VMware Certified Professional on VSphere 4 Study Guide: Exam VCP-410