8 Replies Latest reply on Feb 5, 2020 11:22 AM by mccutcheon3233

    Ipv6

    mccutcheon3233 Novice

      I Just install 2.2 in pure ipv6 environment and i am unable to ssh or ping default gateway of the appliance..

       

       

      any help would be great

        • 1. Re: Ipv6
          kishorenelvagalu Hot Shot
          GS Skyline Support Skyline Community 2/2VMware Employees

          Hello mccutcheon3233,

           

          Welcome to VMware Communities !

           

          SSH is disabled by default on Skyline Appliance. We can enable SSH by following the steps mentioned below

           

          1. Open the Skyline Collector console via the vSphere Client/Web Client
          2. Login as root and the root password defined during deployment
          3. Run 'vi /etc/ssh/sshd_config'
          4. Enter 'i' to modify the file in VI editor
          5. Locate the line that contains 'PermitRootLogin no' and change the value to 'PermitRootLogin yes'
          6. Save the changes by hitting ESC + typing ':wq!'
          7. Restart the sshd service by running 'service sshd restart'

           

          Please check the network configuration using the following KB article

           

          VMware Knowledge Base 

           

          Please share the information requested in the following link if the problem persists

           

          Smartsheet Forms

          • 2. Re: Ipv6
            mccutcheon3233 Novice

            This is not the correct answer if you read my statement I am not even able to ping the default gateway on a ip6 only configuration.

            • 3. Re: Ipv6
              Aditya2018 Hot Shot
              Skyline Community 2/2VMware EmployeesGS Skyline Support

              Hello mccutcheon3233,

               

              I have a few questions to understand the issue further:

               

              1) Please check the output of '/opt/vmware/share/vami/vami_config_net' from the Appliance shell and verify if the network configuration is correct.

              2) Do you have any other VM on the same vSwitch/PortGroup/ESXi using IPv6 only?

              3) Do you have any other VM the same vSwitch which can reach the IPv6 gateway? 

              4) What is the version of vCenter and ESXi running the Skyline Appliance?

               

              Please share your contact details on the following link and let me know a convenient time to contact you: 

               

              https://app.smartsheet.com/b/form/9e31b64730f2419ba2aa50f6c72e66a3

              • 4. Re: Ipv6
                mccutcheon3233 Novice

                1. the conifurations output looks the same as one of my vcenters.

                2. Yes

                3. Yes

                4. Vcenter 6.7u3 esxi 6.7u2

                • 5. Re: Ipv6
                  Aditya2018 Hot Shot
                  Skyline Community 2/2GS Skyline Support VMware Employees

                  Hi mccutcheon3233

                   

                  • Can you please check if you are able to get a response from the Collector Appliance when you initiate a ping from the VM on the same vSwitch, this should confirm any issue with Layer 2 connectivity.
                  • Also please check  '/opt/vmware/etc/lighttpd/lighttpd.conf' on the collector make sure "server.use-ipv6" is set to ”enabled”.
                  • It could also be an issue at the Appliance OS level, try to redeploy the collector once from a fresh source.

                   

                  If the issue persists please share your contact details, we will need to work over a remote session.

                  • 6. Re: Ipv6
                    mccutcheon3233 Novice

                    I have vrops and vcenter running on the same vlan and same host with out any issues.

                     

                    I did check the setting you ask and it is enabled

                    I also have deployed 2.1 version and 2.2 both have the same issue.

                     

                    I will ping you my direct contact information

                    • 7. Re: Ipv6
                      Aditya2018 Hot Shot
                      Skyline Community 2/2GS Skyline Support VMware Employees

                      Hello

                       

                      Able to get ipv6 working for communication.  The issue is with the ip6tables rules, it was not configured to allow input.

                       

                      It can be fixed by running the following command on the shell:

                       

                      #Ip6tables -P INPUT ACCEPT.

                      • 8. Re: Ipv6
                        mccutcheon3233 Novice

                        Yeah i found that over a month ago and gave it to support.  Along with having to run a dual stack for the ip needed to connect to the external services.