VMware Cloud Community
TheDonMiguel
Contributor
Contributor
Jump to solution

Cheap ESX solution (Tests)

Hello community

I'm looking for a cheap hardware solution to play with VMware ESX 3.5, or 3i. Since the new version doesn't work in the Workstation Version it's important to have an alternative Smiley Wink What do I have to consider? What kind of CPU, NIC and Controller are suggested? I would like to use local SATA storage...

Thanks in advanced for the feedback!

Miguel

Tags (3)
Reply
0 Kudos
1 Solution

Accepted Solutions
Dave_Mishchenko
Immortal
Immortal
Jump to solution

Here's a list I'm working on. If you're looking at a whitebox then ideally something with a broadcom / intel Pro /1000 NIC. For a SATA controller the list here should still be fine - , but ESX has a greater number of drivers on the install CD. If you open the CD, go to /vmware/RPMS/ and look for the VMware-esx-drivers-* rpms. If for example, you have a Promise controller open vmware-esx-dirvers-scsi-sata-promise-1.03-64607.i386.rpm. Drill down into the rpm until you find this file - VMware\RPMS\VMware-esx-drivers-scsi-sata_promise-1.03-64607.i386.rpm\VMware-esx-drivers-scsi-sata_promise-1.03-64607.i386.cpio.gz\VMware-esx-drivers-scsi-sata_promise-1.03-64607.i386.cpio\etc\vmware\pciid\sata_promise.xml. You can open it and then you'll see a list of SATA controllers that ESX will recognize. These aren't supported, but they will likely work.

With some SATA controllers (see the source link for the HP ML115 below, you have to make some changes after the install of ESX as the controller is not listed in the XML file, but you can edit it to add support for the card. That assumes that the driver will work with the SATA controller.

Processor wise if you're going with Intel make sure the processor supports Intel VT. Some of the older and lowest priced dual-core CPUs don't. If you're going with a good dual / quad core CPU then a single processor motherboard will be sufficient. You can also look for older servers that were supported with ESX 3.0.x on eBay. I have an older IBM x335/336 that work fine with 3.0.2 - just haven't tested them with 3.5 yet. Downside with them is that they don't have Intel VT so I'm limited to 32 bit VMs on them.

Motherboards and unsupported servers that work with ESX 3.5 / 3i Installable

Last updated - 2008.01.13

Model

SATA Controller

ESX 3.5 b64607

ESX 3i Installable 3.5 b67921

Source / Notes

Servers and PCs

Dell Dimension E521

Working

http://communities.vmware.com/message/833706#833706

Dell PowerEdge SC1430

Working

http://communities.vmware.com/message/838709

HP ML115

MCP55 SATA Controller

Working

Need to update sata_nv.xml - http://communities.vmware.com/thread/116768?tstart=0

Dell XPS - M1710

Intel 82801/GHM (ICH7-M Family)

Working

Tested by vm-help.com

HP Compaq d530 - Small form factor (SFF) DG755A

SATA 82801EB (ICH5)

Working

http://communities.vmware.com/message/833706#833706

HP DC 7100 / 7600 / 7700

Working

http://communities.vmware.com/message/833706#833706

Sun x2200

Working

http://communities.vmware.com/message/833706#833706

Motherboards

ASUS P5M2/SAS

LSI Logic LSI1068 / 82801GB/GR/GH (ICH7 Family)

Working

Tested by vm-help.com. Both the LSI1068 and ICH7 controllers work fine.

Intel S5000PSLROMB

Working

http://communities.vmware.com/thread/116768?tstart=0

GeForce6100SM-M2

NVIDIA GeForce 6100S (MCP61)

Working

Tested by vm-help.com - after install boot into Service Console Mode. Then edit sata_nv.xml to add an entry for the device 03f6. Then run esxcfg-pciid and reboot the server.

Gigabyte GA-K8N51GMF-9

NVIDIA GeForce 6100

Working

http://communities.vmware.com/thread/116768?tstart=0

MSI 915P/G Neo2

Intel ICH6R

Working

http://communities.vmware.com/thread/116768?tstart=0

Supermicro P8SCi

Intel ICH6R

Working

http://communities.vmware.com/thread/116768?tstart=0

SuperMicro X7DBE

Intel Corporation 631xESB/632xESB

Working

HostRAID does not work - http://communities.vmware.com/thread/116768?tstart=0

SuperMicro

Intel 6300ESB Sata Controller

Working

Set controller to SATA only (not IDE-SATA) - http://communities.vmware.com/message/835422

SATA Controllers

Adaptec 2610SA

Untested - should work

Untested - should work

http://communities.vmware.com/message/829936#829936

View solution in original post

Reply
0 Kudos
33 Replies
Dave_Mishchenko
Immortal
Immortal
Jump to solution

Here's a list I'm working on. If you're looking at a whitebox then ideally something with a broadcom / intel Pro /1000 NIC. For a SATA controller the list here should still be fine - , but ESX has a greater number of drivers on the install CD. If you open the CD, go to /vmware/RPMS/ and look for the VMware-esx-drivers-* rpms. If for example, you have a Promise controller open vmware-esx-dirvers-scsi-sata-promise-1.03-64607.i386.rpm. Drill down into the rpm until you find this file - VMware\RPMS\VMware-esx-drivers-scsi-sata_promise-1.03-64607.i386.rpm\VMware-esx-drivers-scsi-sata_promise-1.03-64607.i386.cpio.gz\VMware-esx-drivers-scsi-sata_promise-1.03-64607.i386.cpio\etc\vmware\pciid\sata_promise.xml. You can open it and then you'll see a list of SATA controllers that ESX will recognize. These aren't supported, but they will likely work.

With some SATA controllers (see the source link for the HP ML115 below, you have to make some changes after the install of ESX as the controller is not listed in the XML file, but you can edit it to add support for the card. That assumes that the driver will work with the SATA controller.

Processor wise if you're going with Intel make sure the processor supports Intel VT. Some of the older and lowest priced dual-core CPUs don't. If you're going with a good dual / quad core CPU then a single processor motherboard will be sufficient. You can also look for older servers that were supported with ESX 3.0.x on eBay. I have an older IBM x335/336 that work fine with 3.0.2 - just haven't tested them with 3.5 yet. Downside with them is that they don't have Intel VT so I'm limited to 32 bit VMs on them.

Motherboards and unsupported servers that work with ESX 3.5 / 3i Installable

Last updated - 2008.01.13

Model

SATA Controller

ESX 3.5 b64607

ESX 3i Installable 3.5 b67921

Source / Notes

Servers and PCs

Dell Dimension E521

Working

http://communities.vmware.com/message/833706#833706

Dell PowerEdge SC1430

Working

http://communities.vmware.com/message/838709

HP ML115

MCP55 SATA Controller

Working

Need to update sata_nv.xml - http://communities.vmware.com/thread/116768?tstart=0

Dell XPS - M1710

Intel 82801/GHM (ICH7-M Family)

Working

Tested by vm-help.com

HP Compaq d530 - Small form factor (SFF) DG755A

SATA 82801EB (ICH5)

Working

http://communities.vmware.com/message/833706#833706

HP DC 7100 / 7600 / 7700

Working

http://communities.vmware.com/message/833706#833706

Sun x2200

Working

http://communities.vmware.com/message/833706#833706

Motherboards

ASUS P5M2/SAS

LSI Logic LSI1068 / 82801GB/GR/GH (ICH7 Family)

Working

Tested by vm-help.com. Both the LSI1068 and ICH7 controllers work fine.

Intel S5000PSLROMB

Working

http://communities.vmware.com/thread/116768?tstart=0

GeForce6100SM-M2

NVIDIA GeForce 6100S (MCP61)

Working

Tested by vm-help.com - after install boot into Service Console Mode. Then edit sata_nv.xml to add an entry for the device 03f6. Then run esxcfg-pciid and reboot the server.

Gigabyte GA-K8N51GMF-9

NVIDIA GeForce 6100

Working

http://communities.vmware.com/thread/116768?tstart=0

MSI 915P/G Neo2

Intel ICH6R

Working

http://communities.vmware.com/thread/116768?tstart=0

Supermicro P8SCi

Intel ICH6R

Working

http://communities.vmware.com/thread/116768?tstart=0

SuperMicro X7DBE

Intel Corporation 631xESB/632xESB

Working

HostRAID does not work - http://communities.vmware.com/thread/116768?tstart=0

SuperMicro

Intel 6300ESB Sata Controller

Working

Set controller to SATA only (not IDE-SATA) - http://communities.vmware.com/message/835422

SATA Controllers

Adaptec 2610SA

Untested - should work

Untested - should work

http://communities.vmware.com/message/829936#829936

Reply
0 Kudos
rpartmann
Hot Shot
Hot Shot
Jump to solution

Hi,

best is to use any newer dual/quad core cpu (amd ot intel) and memory. Smiley Wink

Be careful which SATA controllers are on the mainboards. (as Dave.Mishchenko already posted)

I bought additional

PCIe (http://www.intel.com/network/connectivity/products/pro1000pt_desktop_adapter.htm)

and

PCI (http://www.intel.com/network/connectivity/products/pro1000gt_desktop_adapter.htm)

gigabit nics.






ps: Award points if you find answers helpful. Thanks.

ps: Award points if you find answers helpful. Thanks.
xAyiDe
Enthusiast
Enthusiast
Jump to solution

I would like to add the following parts to workinglist, as it runs very fast to:

Gigabyte GA-G33-DS3R (cheap motherboard with build in graphics so ni need for any extra card)

Intel Core 2 Duo E6600 (run at 1.01 Volt but with full speed)

8 Gbyte of Kingston 4x2 GB modules DDR667

LSI logic 8344ELP (8 port SAS)

1 x 150 GB (10k raptor)

2 x 750 Gbyte (7k wd)

1 x Intel Dual Pro 1000MT Server

The above runs very cool and is fast enough for 12-15 servers. power consumption is around 95 watts with CPU loaded.

The onboard Realtek does not work with ESX but I build this for use with VMware Server. Now when ESX 3i is so cheap I will buy that one and run. I have it running on it now and its absolutely stable and runs with good speed. I know I could buy a sevrer for the price of the above stuff, but a sevrer would cost me more electricity, run hotter and make alot more noise without beeing so much faster.

Reply
0 Kudos
jonasb
Contributor
Contributor
Jump to solution

I don't really want to start building my own computer, but what about the HP Quad-core Workstation xw4600 or xw6600?

Will they work out of the box with 3.5?

Reply
0 Kudos
bertdb
Virtuoso
Virtuoso
Jump to solution

This is what I bought a couple of weeks ago:

MSI P35 Platinum motherboard

Intel Core2Quad 2.4 GHz

2x 2GB ram

Promise Sata300 TX2 Plus SATA controller (I bought a card referenced in cat /etc/vmware/pciid/*xml | grep name )

Intel pro/1000 PT Dual port PCI express network card (same, although this one is really on the HCL)

80 GB Sata HD (smallest I could find)

Installed ESX 3.5 over HTTP (CD install booted, but then couldn't find the CD to read the packages from it). Works great.

Reply
0 Kudos
MartynT
Contributor
Contributor
Jump to solution

Would you mind adding the Dell Precision 670 workstation to the list?

Over the weekend I managed to install and run ESX 3.5 with only a minor config change, the change is simple and just requires the CPUID check to be disabled to stop the '0xbad001e' (Unsupported CPU) error on boot. To do this, simply boot into the recovery console, edit the /etc/vmware/esx.conf file and add /vmkernel/checkCPUIDLimit = "FALSE". Reboot, and ESX will boot and function fine. My setup is utilising the 670s onboard (ICH5) SATA controller. The Intel 10/100/1000 onboard network adaptor work fine.

The box spec is as follows:

Precision 670

Dual 3GHz Xeon Processors

8Gb ECC DDR2 400MHz

Intel Pro 100/1000 On board Network Adaptor

1x 40Gb SATA2 HD

1x 500Gb SATA2 HD

I hope this helps,

Thanks,

Martyn

Reply
0 Kudos
rbrambley
Contributor
Contributor
Jump to solution

go to http://vmetc.com/2008/03/14/esx-home-lab-hardware-shopping-list/ for the parts to build a dual core AMD host for $337or a quad core Intel host for $695.

Rich http://vmetc.com
Reply
0 Kudos
vmmeup
Expert
Expert
Jump to solution

I recently built out a 4 host test environment using:

Acer Aspire MT500A Desktop which I picked up for $400.00 on clearance at best buy. The onboard SATA and NIC's didn't work so I order 2 Intel Pro/1000 GT Nics for each host for $29.99 per nic and used a IDE Drive as my boot drive. I have exernal NFS and iSCSI setup for vmfs/vmdk storage. The machines came with 2GB RAM but support up to 8GB so I orderd 4 2GB Sticks per server to mac them out at a price of around $150.00 per server;. So all in all each host ended up costing $580.00.

I have a server that is setup running Centos w/ virtual server that I am using for a storage server. On it I am running multiple storage solutions as vm's. So I was able to remove the 500GB SATA drives that came in the Acer machines and put them into my virtual server machine and was able to gain 2TB of storage in the process. Also reused the 1GB RAM sticks in my storage box, well not all but half of them. End result for just over 2K I have

4 Hosts ESX 3.5 Environent utilizing NFS & iSCSI for storage with over 2TB of storage and multiple storage servers allowing me to test different solutions.

17Ghz Processing Power with 8 Cores

32Gb Ram

Not a bad test environment.......

Sid Smith ----- VCP, VTSP, CCNA, CCA(Xen Server), MCTS Hyper-V & SCVMM08 [http://www.dailyhypervisor.com] - Don't forget to award points for correct and helpful answers. 😉
Reply
0 Kudos
azn2kew
Champion
Champion
Jump to solution

Unfortunately, my ESX is not cheap because I need more power than functional. This box is a beast can run pretty much a lot of servers for testing.

Item

Intel Core 2 Quad Q6600 Kentsfield 2.4GHz

ASUS P5M2/SAS LGA 775 Intel 3000 ATX

G.SKILL 8GB(4 x 2GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Quad Channel

WD5000AAJS 500GB 7200 RPM 8MB Cache SATA 3.0Gb/s (5 drives)

ASUS Black 20X DVDR 8X DVDRW 8X DVD+R DL SATA

Thermaltake Tsunami VA3000BWA Black Aluminum ATX Mid Tower

Thermaltake W0093RU ATX 12V 2.0 Version 500W Power Supply 115/230

Hanns·G HW-191DPB Black 19" 5ms Widescreen LCD Monitor 300 cd/m2 700:1 Built in Speakers

PNY 256MB Video Card DVI

If you found this information useful, please consider awarding points for "Correct" or "Helpful". Thanks!!!

Regards,

Stefan Nguyen

iGeek Systems LLC.

VMware, Citrix, Microsoft Consultant

If you found this information useful, please consider awarding points for "Correct" or "Helpful". Thanks!!! Regards, Stefan Nguyen VMware vExpert 2009 iGeek Systems Inc. VMware vExpert, VCP 3 & 4, VSP, VTSP, CCA, CCEA, CCNA, MCSA, EMCSE, EMCISA
Reply
0 Kudos
techstyled
Contributor
Contributor
Jump to solution

We will be starting our first rollout of VMWare in a week or two. We're using 4 top-end DELL 2950's for the physical hosts and an EMC NS20 for the storage.

I would LOVE to start building a TEST environment right now and I have 3 systems exactly like the cheap AMD system posted earlier as well as plenty of storage options.

However, what I DON'T have are test versions of ESX. How are y'all doing this? Are you just using your production license on test systems?

Reply
0 Kudos
Dave_Mishchenko
Immortal
Immortal
Jump to solution

When you install ESX by default you get a 60 day evalulation period.

Reply
0 Kudos
techstyled
Contributor
Contributor
Jump to solution

My network admin told me that you could only use one "evaluation ESX" evaluation and there's not such for VC.

Is he just misinformed and the "evaluation period" is like with Windows products (i.e. install it to test and just wipe it when done, no activation necessary).

If that's so, I guess you have to have the "real" product first because you don't seem to be able to get more than one trial license via the website.

Not being dense on purpose, just not getting how you can test the whole enchilada.

Reply
0 Kudos
Dave_Mishchenko
Immortal
Immortal
Jump to solution

The evaluation process has changed recently. It used to be that you would get a 30 day eval license for VirtualCenter 2.0x / ESX 3.0.x and the license files would expire and be unusable after that period. Now with VC 2.5 / ESX 3.5 each product will start with a 60 day eval so in theory you could just reinstall on your test systems every 60 days. Not sure what the evaluation license agreement says about that though. When you install and leave it in eval mode you don't have to worry about adding a license file as you would have with VC 2.0.x / ESX 3.0.x.

Reply
0 Kudos
prlyons
Contributor
Contributor
Jump to solution

My ESX lab, parts listed below all purchased from NewEgg:

Item List

MEM 2GX2|A-DATA ADQVE1B16K R - Retail (Qty=2, Price=$139.98)

MB JETWAY JM26GT3-SVP AM2 - Retail (Qty=2, Price=$79.98)

CASE LINKWD|313G-C2628 BK/SIL % - OEM (Qty=2, Price=$55.98)

CPU AMD|A64 X2 4000+ 2.1G AM2 65N R - Retail (Qty=2, Price=$111.98)

FLASH 1G|KST FLDRV DTI/1GBKR R - Retail (Qty=2, Price=$11.98)

Extended Warranty Fee: 0

Subtotal: 399.90

TAX: 0.00

Shipping and Handling Charge**: 44.71

Total: 444.61 Not bad for a 2 node ESX cluster.

Plopped in old Intel 10/100 PCI cards that I had collecting dust in each, ESX 3i installable onto the USB thumb drives, Solaris 10 w/ZFS for ISCSI target, another old solaris box for NFS datastore... The MB supports up to 4 x 2GB RAM, so can grow from 4 GB to 8GB in each server. Also plan on getting a cheap gigabit switch and a few gig NICS. very functional, especially for studying for VCP exam.

Reply
0 Kudos
tuckrman
Contributor
Contributor
Jump to solution

This is an interesting thread. I am looking at building an ESX solution, getting the Asus Mainboard mentioned etc. I currently have a file server with a RocketRAID2220 in it that I have a 2TB RAID array hanging off. Could I use the RocketRAID2220 in my ESX machine ? Have not been able to find any information anywhere as to if anyone has successfully got one of these working. Any information would be much appreciated, cheeres Smiley Happy

Reply
0 Kudos
rpartmann
Hot Shot
Hot Shot
Jump to solution

Hi,

please send us the vendor id/device id of this controller.

on my computer rclick-> manage -> devicemanager -> scsi

controllers -> $YOUR_SCSI_ROCKETRAID -> TAB[details][dewvice instance id]

you will find something PCI\VEN_xxxx&DEV_yyyy&subsys_zzzzzzzz.

But if this controller is some sort of software raid ala promise ...

then it could be that there is no driver for raid funtionality.

hope we can help,

Reinhard.

ps: Award points if you find answers helpful. Thanks.
Reply
0 Kudos
tuckrman
Contributor
Contributor
Jump to solution

Thanks for the prompt reply. Unfortunately you might be right there it might be a software based solution Smiley Sad It seems to be a good card though, seems to work very well under Windows 2003 Server Smiley Happy The details as requested are: PCI\VEN_11AB&DEV_6081&SUBSYS_11AB11AB&REV_09\3&267A616A&0&48 Cheers Smiley Happy

Reply
0 Kudos
tuckrman
Contributor
Contributor
Jump to solution

hey mate, any further information on the above ? Thanks Smiley Happy

Reply
0 Kudos